The GPeR unit allows to extend Ethernet cable by additional hop (< 100 - 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m.
Handy for highrise buildings, multi-apartment buildings, with many floors and sections, where very long Ethernet cables might be a problem.
Maximium allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m (depending on cable quality, high quality - up to 150 m).
Maximium allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality).
In case if the destination device does not support PoE-in powering, the PoE Passthrough can be disabled by manually removing all jumpers.
The GPeR unit allows to extend Ethernet cable by additional hop (< 100 - 150 m to regular network devices, and up to 210 m to another GPeR unit) up to 1,500 m.
Handy for highrise buildings, multi-apartment buildings, with many floors and sections, where very long Ethernet cables might be a problem.
Maximium allowed length of CAT6 Ethernet cable between GPeR and power source/router is up to 100 m (depending on cable quality, high quality - up to 150 m).
Maximium allowed distance of CAT6 Ethernet cable between two GPeR devices is up to 210 m (depending on cable quality).
In case if the destination device does not support PoE-in powering, the PoE Passthrough can be disabled by manually removing all jumpers.
The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device.
Helps reducing number of wires that lead up the tower.
For using with any RouterBOARD that supports 9-48V PoE.
The GPOE has shielded connectors.
The ePoE technology of Dahua adopts advanced 2D-PAM3 coding modulation from physical layer, and realizes full duplex transmission over 800 meters at the speed of 10Mbps, or 300 meters at the speed of 100Mbps via Cat5 or coaxial cable media. Dahua ePoE technology offer a new way to accomplish long distance transmission between IP camera and network switch....
The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. The GPEN11 is part of the GPEN (Gigabit Passive Ethernet Network) concept, which aims to replace GPON installations with lower cost and more easy to deploy ethernet alternative.
UTP passive PoE adapter kit, 0.15 m
- Perfect for use with IP-cameras
- Transfers power and data over single Ethernet cable
- Plug and Play: no installation or configuration required
- This passive Power over Ethernet injector + splitter adapter kit is an ideal solution to supply e.g. your IP Camera with power and data without adding an extra...
GESP
New revision of Gigabit Ethernet Surge Protector in IP67 waterproof enclosure
GESP is Gigabit Ethernet Surge Protector that can be used to protect the network from lightning or surge damages.
Here’s what a typical use-case would be like. You have a mast with some antennas. And some switches on the ground. Put the GESP surge protectors on...
GPEN21
Smart power injector that serves as an advanced software controlled repeater
The GPEN21 is a smart power injector that serves as an advanced software controlled repeater. Not only can it power your uplink devices via PoE, it can also provide a range of useful software features:
• Interface management and monitoring
• GPEN link...
PoE+ Midspan
> Supports IEEE802.3af, IEEE802.3at standard
> Conform IEEE802.3, IEEE802.3u and IEEE802.3ab standards
Ethernet Port: 1*10/100/1000 Base-T, 1*10/100/1000 Base-T( PoE power supply)
Power output ≤30W
PoE Protocol: IEEE802.3af, IEEE802.3at
Power AC100~240V 50/60Hz
Working Temperature -10°C~55°C
Weight 250g
Dimension:...
- Support passive PoE cascade power supply and Ethernet data exchange
- Support IEEE 802.3af/at standard power supply IP Camera
- Cooperating with High PoE Midspan (TAM01GT01GT-75W), able to cascade level 2 PoE Extender, connect to 3 IPC (power consumption